Material Calculator

This calculator will estimate the amount of material for making a pour mold of a simple cubic model. Click here for detailed Material Estimators and Advanced Calculators ›

Cubic Dimension of Model:
in × in × in
Cubic Dimension of Mold Box:
in × in × in
Specific Volume of the Material: in3/lb
This mold will require approximately  lbs () of material.

This calculator will estimate the amount of casting material for a simple cubic part. Click here for detailed Material Estimators and Advanced Calculators ›

Cubic Dimension of Mold Cavity:
in × in × in
Specific Volume of the Material: in3/lb
This casting will require approximately  lbs () of material.
Please note: We do our best to ensure that this material estimator is accurate. However, Smooth-On offers no warranty either expressed or implied regarding the accuracy/reliability of this information. Smooth-On assumes no liability for loss or damage associated with use of material estimators. If this is a critical project, we encourage you to verify estimator results using the long-hand method of correlating the volumetric yield of the material with mold cavity. You can also contact us for assistance.

Tools & Equipment

There are tools and equipment that can make processing easier and ensure success with these materials.
(read more)

Items 1 to 12 of 15 total

per page
Page:
  1. 1
  2. 2

Set Ascending Direction
  1. Vacuum Chamber - Large ›

    Vacuum Chamber - Large

    Vacuum Chamber For Vacuuming Liquid Rubbers and Liquid Plastics, can accommodate up to a 5-Gallon pail.
  2. Turbine Mixer ›

    Turbine Mixer

    The Turbine Mixer is a simple design, yet does a better job of mixing Smooth-On rubbers, plastics and foams than any mixer we've tried.
  3. Static Mixers For 400 ml. Cartridges - Bag of 10 ›

    Static Mixers For 400 ml. Cartridges - Bag of 10

    These mixers are used along with a dispensing gun to mix material in 400 ml. cartridges as it is dispensed.
  4. Pressure Chamber ›

    Pressure Chamber

    Pressure pot for pressure casting. 5 gallon size. 80 psi max pressure.
  5. Mixing Containers ›

    Mixing Containers

    Plastic mixing containers with graduated markings for accurate measurement of materials which are measured by volume.

    Starting at: $6.31

    Learn More 
  6. Manual Dispensing Gun ›

    Manual Dispensing Gun

    Dispenses 400 ml. cartridges of mold rubber with squeeze of handle.
  7. Kwikee Sprayer - Non-Aerosol Sprayer ›

    Kwikee Sprayer - Non-Aerosol Sprayer

    The Kwikee sprayer delivers sealing agent or release agent in a fine mist.
  8. Ez-Spray® Jr Flow Restrictors ›

    Ez-Spray® Jr Flow Restrictors

    Flow restrictors for use with the EZ-Spray Jr.® system.
  9. Ez-Spray Jr. Spray Gun® - 1500ml ›

    Ez-Spray Jr. Spray Gun® - 1500ml

    Gun for spraying 1500 ml cartridges of EZ-Spray materials.
  10. EZ-Spray Jr. SMALL Static Mixers -Bag Of 10 (Includes Spray Tip) ›

    EZ-Spray Jr. SMALL Static Mixers -Bag Of 10 (Includes Spray Tip)

    Bag of 10 EZ-Spray Jr SMALL Static Mixers for EZ-Spray 45, EZ-Spray Plastic, and EZ-Spray Styrocoat. Includes Spray Tip.
  11. EZ-Spray Jr. LARGE Static Mixers -Bag Of 10 (Includes Spray Tip) ›

    EZ-Spray Jr. LARGE Static Mixers -Bag Of 10 (Includes Spray Tip)

    Bag of 10 EZ-Spray Jr LARGE Static Mixers for EZ-Spray Silicone 20 and EZ-Spray Silicone 35. Includes Spray Tip.
  12. EZ-Spray Jr. Large Static Mixer Adapter ›

    EZ-Spray Jr. Large Static Mixer Adapter

    This adapter is REQUIRED if you have a RED COLORED EZ-SPRAY JR.GUN SYSTEM

Items 1 to 12 of 15 total

per page
Page:
  1. 1
  2. 2

Set Ascending Direction